How To Make a Laptop Cooling Pad

How To Make a Laptop Cooling Pad – DIY Laptop Coolers (2021)

For everyday users on the go, the heat generated by the laptop can be damaging for both it and the user. With laptops constantly generating heat, cooling pads are an essential tool for keeping the machine running at optimal speeds.

A laptop’s cooling pad will work on both hot and cold laptops to keep them at an ambient temperature. The heat generated by laptops is not only damaging to the computer but can be dangerous to the user as well.

How to make a laptop cooling pad? In this article, Crane Stand will provide you with a step-by-step guide on building a cooling pad for your laptop?

Let’s get started!

Laptop Cooling Pad DIY – Step by step Guide

Laptop Cooling Pad DIY - Step by step Guide (1)

Step 1: Take Measurements

Take measurements of the length and width of your laptop. Note down these measurements for future reference.

Step 2: Cut the wood

Make sure to cut the plywood or any other wood to your desired size.

Make sure it is slightly bigger than the dimensions of your laptop. For extra space, add 2 centimeters (0.75 inches) to each side. The wood should be approximately 1.25 cm (0.5 inches thick).

After cutting, measure the wood. Adjust, if necessary.

Step 3: Make holes.

Drilling holes for making a Laptop Cooling Pad

In a grid-like pattern on the board, place the holes approximately 2 cm (0.75 inches). The holes should be large enough to accommodate a pencil, but not more.

Drill the holes closer together if you are experiencing severe overheating issues.

Fans will also be required to be purchased and plugged into each hole. You can also disassemble an existing fan you don’t use.

Next, sand the rough edges to avoid splinters.

Step 4: Add Feet

If your laptop doesn’t have feet (pads that raise it), glue something to raise the pad. This is essential to ensure adequate air circulation.

This image shows how to make feet from wood; it is an excellent way to use scrap wood.
You can also buy small rubber, plastic, or similar feet at your local hardware store. Non-slip designs work best.

Step 5: Decorate the Pad

Decorate the Pad

Lightly vacuum the board. This will stop any wood particles from being sucked into your computer’s fan. The fans should be screwed under the board. Attach the fans to the holes that you have made.

You can personalize your cooling pad with any paint. Use paint that matches your laptop if you’re not very artistic. A wood stain could be used if the wood is not particleboard.

Done. To keep your laptop cool during use, place it on the pad.

Check our guide to know if Laptop Cooling Pad Works or not: https://www.thecranestand.com/does-laptop-cooling-pad-work/

FAQs

Are cooling pads bad for laptops?

The purpose of the cooling pad is to keep the laptop cool so it doesn’t overheat and shut down. The pads are designed to act as a barrier between the laptop and desk, allowing air to flow underneath, but they can often cause desk surfaces to heat up when in use for long periods of time.

Depending on the pad and the level of heat transfer, the heat that transfers into your desk may increase or decrease.

Can a laptop be water-cooled?

A laptop can’t be water-cooled as they don’t have fans or vents which can bring fresh air into the computer to keep it cool. The laptop’s processor is usually not the limiting factor in performance. However, this may change as processors increase in size and power.

Some laptops can be water-cooled with a special tube and hose called a hose-based loop. This would require computer case modification and may not be recommended by the manufacturer.

Can I use a laptop while charging?

It’s not recommended to use your laptop while it is charging because this can put a lot of stress on the battery and it could lead to the battery wearing out quickly.

Plus, with mobile devices becoming more and more powerful with each generation, you’re asking for trouble if your laptop is hooked up to an external charger.

Can the cooling pad replace the laptop fan?

The cooling pad may be able to keep the temperature down enough to reduce the heat output of the laptop, but it won’t be able to replace the fan. Computer cooling pads are designed to remove heat from the CPU by drawing air through the metal.

A great way to cool your computer is to buy a cooling pad. These pads can be placed on top of your laptop to keep the laptop cool.

A cooling pad is a soft pad that rests on top of your laptop and can absorb some of the heat that comes from the CPU.

Do laptop cooling pads drain the battery?

The answer to this question depends on the type of device. If you are using a laptop cooling pad designed for your specific device, then no it will not have any effect on your battery life. If you are using a generic cooling pad for laptops, then it will drain your battery more quickly, because it does not provide enough power for your device.

Conclusion

That’s our guide for making a laptop cooling pad. Now you can make one for your device and rest assured you are using the best material. The most important thing to remember is to make sure the pad does not heat up your device, and it should have enough power to run your laptop without a problem.

Thank you for reading our article, hope you enjoyed it. Have a good day!

Video:

Leave a Comment

Your email address will not be published. Required fields are marked *